9 Simple Steps to Waterproofing Exterior Walls

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

The outer part of the wall is usually covered with a lot of dust and dirt from the air. To ensure the efficiency of the entire process, you need to clear off the debris and dust thoroughly. The dirt and debris should be cleaned with a broom, brush, or scraper. Then wash it with a power washer.

Step 3: Check out for the cracks and fill them up

Cracks and holes can develop on your exterior walls over time. Follow up the cleaning process with a thorough look at the cracks and holes in the wall. Simply fill them up with cement.

Most of homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV, you find websites and programs with step-by-step guides for DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

It is possible to seal the cracks with a cement mixture. Make sure to remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply cement. After applying the cement in the crevices, let it dry, then apply the waterproof paint seal for the walls. Let it become dry after that.

Step 5: Pick the right water-proofer

There are many waterproof products available in the market. You have to pick the one that goes with the wall. The water-proofer should be chosen based on whether it is a concrete wall or a silicate-based one.

You can choose between a silicate-based concrete sealer and a concrete coating. Pick a plaster waterproof Additive that will strengthen your walls.

Step 6: Apply the water-proofer

Apply the water-proofer thoroughly on the walls with either a roller or brush. If you want to apply more than one coat, give a thin coat first. Add the second coating after the first one has dried.

Step 7: Apply tar and heavy-duty membrane

“If you want to add more strength to the layer, you need to use a tar-based pitch after you’ve dried the cement. It should be applied everywhere on your wall.”

After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your walls.

Step 8: Consider adding gravel

To lay the drainage pipes, you need a proper base below the footer. The drainage pipes will get adequate support from a gravel base. Gravel is long-lasting and provides better protection.

You need to lay the drainage pipe cover and gravel. Next to the footer, level the gravel and then back-fill it. A covering for the pipe should be at least 3 inches.

Step 9: Add a fabric barrier

Along with a fabric barrier, secure the pipe. Ensuring a fabric barrier is going to prevent the formation of dirt and keep your system clean. Then back-fill the trench and build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after you

Conclusion:

Good waterproofing gives your home a new life and strength to deal with outside issues. If you want good waterproof solutions for your walls, Magicrete is here to help. At a very low and affordable price, Magicrete can help you with your outdoor needs.